DESIGN AND FABRICATION OF A PRINTING I BLOCK MACHINE – MECHANICAL ENGINEERING Project Topics – Complete project topic

[ad_1]

ABSTRACT
 
Parameters on which clear prints depends were comprehensively investigated.  The study revealed that clear print depends on the impressed pressure the working temperature and the gold foil print paper life expectancy.
Also studies were he manner of dependence of these parameters on prints impressed  on sheets of varied thickness.  The results of these investigation were  utizlied in the design and fabrication of an operational manual printing machine using gold foil   sheet depositor clear prints were impressed on papers during the new machine’s operation.

LIST OF TABLES
TABLE 1  – Experimental determination of pressure for printing 
11- Effect of temperature on sharpness of print.
111 ” Description of (components) parts and materials use for them
1v- comparison of cost and properties of materials 
LIST OF FIGURES
Description
Figure 1 sketch of alternative A
Figure 2. Sketch of alternative B.
Figure 3 sketch of alternative C
Figure 4 isomeric view of hot plate square housing 
Figure 5 isometric view of type holder
Figure 6 &7 load and free body diagram of crank are (Handle) and rod.
LIST OF SYMBOLS
A ” Area
A ” Acceleration
D ” Maximum shaft diameter
d- minimum  shaft diameter 
e- efficiency 
k ” Thermal conductivity
c ” Heat capacity
x ” The pressure transmissibility of lever system (press x  1/duration )
t ” Time
l ” Length of shaft
m ” Mass
m ” Maximum bearding moment
p – Electric power
q ” Quantity of heat 
TABLE OF CONTENTS
Title page ii
Letter of transmittal iii
Release iv
Approval page v
Dedication vi
Acknowledgement vii
Abstract viii
List of figures ix
 List of tables x
List of symbols xi
Table of contents xii
CHAPTER ONE 
1.1 introduction 1
1.2 literature review and data collection 2
1.3 experimental determination of pressure for prating 3
1.4 design specification 9
CHAPTER TWO
2.1 Design solutions 11
2.2 Alternative A press foot printer 11
2.3 Alternative  B; crank arm  (handle ) 14
2.4 Alternative  C; automatic (motorized) printer 17
2.5 Comparison of alternative and choice 20
CHAPTER THREE
3.1 Design selection and analysis of parts of chosen alternative 22
3.2 Theory of  design/  design calculation 24
3.3 The  design of the shaft (Hollow) 26
CHAPTER FOUR
4.1 construction of prototype 28
4.2 general 28
4.3 material selection 29
4.4 sequence of construction and assembly 40
CHAPTER FIVE
5.1 Testing of prototype (test ” run) 40
5.2 Evaluation of machine efficiency 40
5.3 Operator’s manual 41
5.4 Costing  (cost analysis) 42
5.5 Problems Encounter 45
5.6 Conclusion 45
5.7 Recommendation 46
REFERENCES

[ad_2]


Purchase Detail

Hello, we’re glad you stopped by, you can download the complete project materials to this project with Abstract, Chapters 1 – 5, References and Appendix (Questionaire, Charts, etc) for N5000 ($15) only,
Please call 08111770269 or +2348059541956 to place an order or use the whatsapp button below to chat us up.
Bank details are stated below.

Bank: UBA
Account No: 1021412898
Account Name: Starnet Innovations Limited

The Blazingprojects Mobile App



Download and install the Blazingprojects Mobile App from Google Play to enjoy over 50,000 project topics and materials from 73 departments, completely offline (no internet needed) with the project topics updated Monthly, click here to install.

0/5 (0 Reviews)
Read Previous

PROBLEMS AND PROSPECTS OF USING FAKE NIGERIAN NATIONAL ID BY FOREIGNERS CRIMINOLOGY Project Topics – Complete project material

Read Next

THE NEED FOR EFFICIENT SUPPLY MANAGEMENT IN THE PUBLIC SECTOR (A CASE STUDY OF MINISTRY OF FINANCE IMO STATE) – PURCHASING AND SUPPLY Project Topics – Complete project material

Need Help? Chat with us