1.1     BACKGROUND OF THE STUDY

Biodiesel (fatty acid methyl esters) is an alternative fuel for diesel engines. It is an alcohol ester product from the transesterification of triglycerides in vegetable oils or animals accomplished by reacting lower alcohols such as methanol or ethanol with triglycerides.

The National Biodiesel Board (USA) technically defined biodiesel as a mono-alkyl ester. Blends of biodiesel and conventional hydrocarbon based diesel are products most commonly distributed for use in the retail diesel fuel market place. Biodiesel contain no petroleum, but it can be blended at any level with petroleum diesel to create a biodiesel blend. Much of the world uses a system known as the “B” factor to state the amount of biodiesel in any fuel mix:

• Ø 100% biodiesel is referred to as B100.
• Ø 20% biodiesel, 80% petrodiesel is labelled B20.
• Ø 5% biodiesel, 95% petrodiesel is labelled B5.
• Ø 2% biodiesel, 98% petrodiesel is labelled B2.

Blends of less than 20% biodiesel can be used in diesel equipment with no, or only minor modifications. Biodiesel can also be used in its pure form (B100), but may be blended with petroleum diesel at any concentration in most injection pump diesel engine. New extreme high-pressure (29000 psi) common rail engine have strict factory limits of B5 or B20 depending on manufacturers.

Biodiesel has different solvent properties than petrodiesel, and will degrade natural rubber gaskets and hoses in vehicles (mostly vehicles manufactured before 1992), although these tend to wear out naturally and most likely will have already been replaced with FKM, which is non reactive to biodiesel.

The first diesel engine was produced by Rudolf in Augsburg and Germany. In remembrance of this event, August 10 has been declared “International Biodiesel Day”. Rudolf diesel demonstrated a diesel running on pea nut (at the request of the French government) but for the French otto company at the world fair in Paris, France in 1990. (Knothe, 2001).

Biodiesel has been known to breakdown deposits of residue in the fuel lines where petrodiesel has been used. As a result, fuel filters may become clogged with particulates of a quick transition to pure biodiesel is made. Therefore, it is recommended to change the fuel filters on engine and heaters shortly after switching to a biodiesel blend.

Biodiesel is light to dark yellow liquid immiscible with water, with high boiling point and low vapour pressure. It has been used as a substitute for diesel fuel in the automobile industry and also referred to as a diesel – equivalent processed fuel derived from vegetable oils. (Biodiesel, 2007).

Several research have been performed on the production of biodiesel and some basic feedstock for the fuel includes animal fats, vegetable oils, soy, rapseed, jatropha, mahua, mustard, flax, sunflower, palm oil, hemp, field pennycress, pongamiapinnata and algae. Pure biodiesel is the lowest emission diesel fuel. Although liquefied petroleum gas and hydrogen have cleaner combustion, they are used to fuel much less efficient petrol engines and are not as widely available. Biodiesel is an oxygenated fuel, meaning that it contains a reduced amount of carbon and higher hydrogen and oxygen content than fossil diesel. This improves the combustion and reduces the particulate emission from un-burnt carbon. Biodiesel is also safe to handle and transport because it is as biodegradable as sugar, ten times less toxic than table salt, has a high flash point of about 300oF (148oC) compared to petroleum diesel fuel, which has a flash point of 125oF (52oC). Current commercial production of biodiesel (FAME) is via homogeneous transesterification but this process has a lot of limitations, thus, making the cost of biodiesel not economical as compared to petroleum-derived diesel. One of the most significant limitations using this process is the formations of soap in the product mixture leading to additional cost required for the separation of soap from the biodiesel. Also, the formation of soap has also led to the loss of triglycerides molecules that can be used to form biodiesel. However, since the catalyst and the reactants/products are in the same phase, the separation of products (biodiesel) from the catalyst becomes complex. On the other hand, heterogeneous transesterification can overcome all these limitations in which solid based catalyst is used in place of homogeneous catalyst, making it a more efficient process for biodiesel production with lower cost and reduced environmental impact.

Xie et al. studied the transesterification of soybean oil to methyl ester using potassium-loaded alumina catalyst. Also, Suppes et al. studied the transesterification reaction of soybean oil with zeolite and metal catalysts for the production of biodiesel, while Jitputti et al. studied the transesterification of crude palm kernel oil and crude coconut oil using several acidic and basic solids.

All these study indicated that different oils would require different catalyst for optimum conversion to biodiesel. {International Conference on Environment 2008 (ICENV 2008)}

GET THE COMPLETE PROJECT»

Do you need help? Talk to us right now: (+234) 8111770269, 08111770269 (Call/WhatsApp). Email: projects@blazingprojects.com.

IF YOU CAN’T FIND YOUR TOPIC, CLICK HERE TO HIRE A WRITER»

Disclaimer: This PDF Material Content is Developed by the copyright owner to Serve as a RESEARCH GUIDE for Students to Conduct Academic Research. You are allowed to use the original PDF Research Material Guide you will receive in the following ways: 1. As a source for additional understanding of the project topic. 2. As a source for ideas for you own academic research work (if properly referenced). 3. For PROPER paraphrasing ( see your school definition of plagiarism and acceptable paraphrase). 4. Direct citing ( if referenced properly). Thank you so much for your respect for the authors copyright. Do you need help? Talk to us right now: (+234) 8111770269, 08111770269 (Call/WhatsApp). Email: projects@blazingprojects.com.

Related